Relationship between physical and mechanical properties of jointed rocks in Central Iran (Bafgh Block) | |
| روش های تحلیلی و عددی در مهندسی معدن | |
| مقاله 1، دوره 12، شماره 31، مرداد 1401، صفحه 1-13 اصل مقاله (2.97 M) | |
| نوع مقاله: مقاله پژوهشی | |
| شناسه دیجیتال (DOI): 10.22034/anm.2022.2026 | |
| نویسندگان | |
| Seyed Hadi Beheshti1؛ Alireza Yarahmadi Bafghi1؛ Ahmad Ghorbani* 1؛ Mohammad Reza Rezvanianzadeh2 | |
| 1Dept. of Mining and Metallurgy Engineering, Yazd University, Yazd, Iran | |
| 2Nuclear Science and Technology Research Institute, Atomic Energy Organization of Iran, Tehran, Iran | |
| چکیده | |
| Central Iran is one of the active mining zones of Iran and has great mining potential. Large iron mines such as Choghart, Chadormalu, Sechahoon, Chahgaz, Lake Siah, Mishdavan, etc. are located in this zone. Other metals also exist in this zone Like lead and zinc in Koushk, Chahmir, and Taj-Kooh mines. Also, non-metallic deposits such as Fahraj limestone mines and building stone mines such as Bishedar marble, Taft travertine, Shirkooh granite, etc. are being extracted in this zone. Considering mineral resources and current explorations, the mines continue to develop and one of the important topics in the exploration and exploitation phase is the study of geomechanical conditions in the zone under study. The relationship between the physical and mechanical properties of rocks makes it possible to predict the strength of the intact rock which can be used in preliminary designing of the mine at less cost and less time and just with some simple tests on exploratory boreholes and surface samples. It can also be used in mines under extraction to gain more comprehensive knowledge of the mechanical properties of mine rocks. In this study, mechanical properties such as uniaxial compressive strength, point load, indirect tensile strength (Brazilian) as well as physical properties of rock such as density, porosity, compressive wave velocity (P-wave), and electrical resistivity were measured on selected samples taken from Choghart, Sechahoon, Lakeh Siah, Koushk, Bishehdar marble, Taft travertine, Ravar sandstone and the cores of 5 geotechnical boreholes from the Anomaly VI of Central Iran Iron Ore and 4 geotechnical boreholes of Chahgaz iron ore mine. The purpose of these measurements is to investigate the relationship between mechanical and physical properties of the samples, especially electrical resistivity. In the first step, 300 surface and depth samples were collected from the mines mentioned above. After preparing the cores, effective porosity and density were recorded according to the standards (weighing the saturated and dry sample method). Also, the electrical resistivity was calculated by measuring the voltage and electrical current in the samples. The results demonstrated that there is a high correlation between P-wave velocity and electrical resistivity in all the samples. Furthermore, both parameters of P-wave velocity and electrical resistivity are dependent on porosity, and electrical resistivity like P-wave velocity has a good relationship with the mechanical properties of sedimentary rocks and volcano-sediments. Hence, the special electrical resistivity can be used as a non-destructive test to estimate the mechanical properties of rocks. Additionally, the presence of metal ores in the samples in low percentages does not cause errors in estimating physical and mechanical parameters as long as density is less than 2.8 gr/cm3. For samples with high metal content, induced polarization measurements can reduce the uncertainty of the electrical resistivity. | |
| کلیدواژهها | |
| Electrical Resistivity؛ Compressive Wave Velocity؛ Physical Properties؛ Mechanical Properties؛ Central Iran | |
| عنوان مقاله [English] | |
| Relationship between physical and mechanical properties of jointed rocks in Central Iran (Bafgh Block) | |
| نویسندگان [English] | |
| Seyed Hadi Beheshti1؛ Alireza Yarahmadi Bafghi1؛ Ahmad Ghorbani1؛ Mohammad Reza Rezvanianzadeh2 | |
| 1Dept. of Mining and Metallurgy Engineering, Yazd University, Yazd, Iran | |
| 2Nuclear Science and Technology Research Institute, Atomic Energy Organization of Iran, Tehran, Iran | |
| چکیده [English] | |
| Central Iran is one of the active mining zones of Iran and has great mining potential. Large iron mines such as Choghart, Chadormalu, Sechahoon, Chahgaz, Lake Siah, Mishdavan, etc. are located in this zone. Other metals also exist in this zone Like lead and zinc in Koushk, Chahmir, and Taj-Kooh mines. Also, non-metallic deposits such as Fahraj limestone mines and building stone mines such as Bishedar marble, Taft travertine, Shirkooh granite, etc. are being extracted in this zone. Considering mineral resources and current explorations, the mines continue to develop and one of the important topics in the exploration and exploitation phase is the study of geomechanical conditions in the zone under study. The relationship between the physical and mechanical properties of rocks makes it possible to predict the strength of the intact rock which can be used in preliminary designing of the mine at less cost and less time and just with some simple tests on exploratory boreholes and surface samples. It can also be used in mines under extraction to gain more comprehensive knowledge of the mechanical properties of mine rocks. In this study, mechanical properties such as uniaxial compressive strength, point load, indirect tensile strength (Brazilian) as well as physical properties of rock such as density, porosity, compressive wave velocity (P-wave), and electrical resistivity were measured on selected samples taken from Choghart, Sechahoon, Lakeh Siah, Koushk, Bishehdar marble, Taft travertine, Ravar sandstone and the cores of 5 geotechnical boreholes from the Anomaly VI of Central Iran Iron Ore and 4 geotechnical boreholes of Chahgaz iron ore mine. The purpose of these measurements is to investigate the relationship between mechanical and physical properties of the samples, especially electrical resistivity. In the first step, 300 surface and depth samples were collected from the mines mentioned above. After preparing the cores, effective porosity and density were recorded according to the standards (weighing the saturated and dry sample method). Also, the electrical resistivity was calculated by measuring the voltage and electrical current in the samples. The results demonstrated that there is a high correlation between P-wave velocity and electrical resistivity in all the samples. Furthermore, both parameters of P-wave velocity and electrical resistivity are dependent on porosity, and electrical resistivity like P-wave velocity has a good relationship with the mechanical properties of sedimentary rocks and volcano-sediments. Hence, the special electrical resistivity can be used as a non-destructive test to estimate the mechanical properties of rocks. Additionally, the presence of metal ores in the samples in low percentages does not cause errors in estimating physical and mechanical parameters as long as density is less than 2.8 gr/cm3. For samples with high metal content, induced polarization measurements can reduce the uncertainty of the electrical resistivity. | |
| مراجع | |
|
[1] D'Andrea, Dennis V, D. E Fogelson, and R. L Fischer. Prediction of Compressive Strength from Other Rock Properties. [Washington, D.C.]: U.S. Dept. of the Interior, Bureau of Mines, 1965.
[2] Gaviglio, P. Longitudinal waves propagation in a limestone: The relationship between velocity and density. Rock Mech Rock Engng 22, 1989.p. 299–306
[3] Cargill, J.S., and A. Shakoor. Evaluation of Empirical Methods for Measuring the Uniaxial Compressive Strength of Rock. International Journal of Rock Mechanics and Mining Sciences & Geomechanics, 1990. Abstracts 27, no. 6: 495–503.
[4] Chau K.T. and Wong R.H.C. Uniaxial compressive strength and point load strength of rocks International Journal of Rock Mechanics and Mining Science & Geomechanics Abstract, Vol. 33, No. 2, 1996. p. 183-188.
[5] Brovtsyn, A.K., Chershneva, G.S. Experimental Ultrasonic Study of the Moisture Content of Clay Rocks. Refractories and Industrial Ceramics 41, 2000. p.320–321
[6] S Kahraman, Evaluation of simple methods for assessing the uniaxial compressive strength of rock, International Journal of Rock Mechanics and Mining Sciences, Volume 38, Issue 7, 2001. p. 981-994.
[7] Kahraman, S., Yeken, T. Determination of physical properties of carbonate rocks from P-wave velocity. Bull Eng Geol Environ 67,2008. p.277–281
[8] S. Kahraman, A correlation between P-wave velocity, number of joints and Schmidt hammer rebound number, International Journal of Rock Mechanics and Mining Sciences, Volume 38, Issue 5, 2001. P. 729-733.
[9] Sharma, P.K., Singh, T.N. A correlation between P-wave velocity, impact strength index, slake durability index and uniaxial compressive strength. Bull Eng Geol Environ 67, 2008. P. 17–22.
[10] Sarno A I. Correlations of static dynamic and physical properties to the weathering state of Ocala limestone MScThesis University of North Florida, Jacksonville, 2010.
[11] Kurtuluş, C., Irmak, T.S. & Sertçelik, I. Physical and mechanical properties of Gokceada: Imbros (NE Aegean Sea) Island andesites. Bull Eng Geol Environ 69, 2010. P.321–324.
[12] Yagiz, S. P-wave velocity test for assessment of geotechnical properties of some rock materials. Bull Mater Sci 34, 2011. p.947.
[13] A. M. Sheraz, M. Z. Emad, M. Shahzad, and S. M. Arshad., Relation between uniaxial compressive strength point load index and sonic wave velocity for dolerite. Pakistan Journal of Science Vol. 66 No. 1, 2014.
[14] Kurtulus, C., CakIr, S. & Yoğurtcuoğlu, A.C. Ultrasound Study of Limestone Rock Physical and Mechanical Properties. Soil Mech Found Eng, 2016. p. 52, 348–354.
[15] Amin Jamshidi, Hasan Zamanian, Reza Zarei Sahamieh, The effect of density and porosity on the correlation between uniaxial compressive strength and P-wave velocity. Rock Mechanics and Rock Engineering,Volume 51, Issue 4,2018. p. 1279-1286.
[16] Amin Jamshidi, Hasan Zamanian, Reza Zarei Sahamieh, Correlation between mechanical properties of sandstones and P-wave velocity in different degrees of saturation. Geotechnical and Geological Engineering,2018. p. 1-10.
[17] Shobeir Arshadnejad; Mohammad Javad Arab. "Relationship between Porosity and Density and Point Load Index for Magnetite (Case Study: Sarvian Mine)". Road, 28, 102, 2020, 59-66.
[18] Sh. Arshadnejad; M. J. Arab. "Relationship between Porosity and Density on Tensile Strength of Magnetite-Case Study: Sarvian Mine". Road, 26, 95, 2018, 151-159.
[19] Liera .F. J. et al., Temperature dependence of the electrical resistivity of water‐saturated rocks. GEOPHYSICS,55(5), 1990. p.576.
[20] Matsui T, Park S G, Park M K and Matsuura S. Relationship between electrical resistivity and physical properties of rocks ISRM Int. Symp. (Int. Society for Rock Mechanics), 2000.
[21] Roberts J J, Bonner B P and Duba A G Electrical resistivity measurements of andesite and hydrothermal breccia from the Awibengkok geothermal field Indonesia 25th Annual Stanford Geothermal Reservoir Engineering Workshop ,2000. p. 339–44.
[22] Roberts J J, Bonner B P and Kasameyer P W Electrical resistivity measurements of intact and fractured geothermal reservoir rocks Proc. 26th Annual Stanford Geothemuzl Reservoir Engineering Workshop,2001a.
[23] S.G. Park, S.W. Shin, D.K. Lee, C.R. Kim and J.S. Son, Relationship between Electrical Resistivity and Physical Properties of Rocks. European Association of Geoscientists & Engineers, Conference Proceedings, Near Surface Geoscience 2016 - First Conference on Geophysics for Mineral Exploration and Mining, Volume 2016, 2016, p.1 - 5.
[24] Awang, Haryati, and Cho Gye-Chun. "Resistivity laboratory measurement of geomaterial." Electron. J. Geotech. Eng 21 ,2016. p.211.
[25] KAHRAMAN, S., YEKEN, T. Electrical resistivity measurement to predict uniaxial compressive and tensile strength of igneous rocks. Bull Mater Sci 33, 2010. p.731–735.
[26] İbrahim Sertçelik, Cengiz Kurtuluş, Fadime Sertçelik, Ertan Pekşen, Metin Aşçı, Investigation into relations between physical and electrical properties of rocks and concretes, Journal of Geophysics and Engineering, Volume 15, Issue 1, February 2018. p. 142–152.
[27] ASTM Standard 1978Standard method for laboratory determination of pulse velocities and ultrasonic elastic constants of rocks Annual Book of ASTM Standards Part 19 D2845–69:356–363 (Philadelphia, PA: American Society for Testing and Materials).
[28] ASTM Standard 1984Standard test method for unconfined compressive strength of intact core specimens soil and rock building stones Annual Book of ASTM Standards 4.08 (Philadelphia, PA: American Society for Testing and Materials).
[29] ASTM Standard 2001Standard Practice for Preparing Rock Core Specimens and Determining Dimensional and Shape Tolerances (Philadelphia, PA: American Society for Testing and Materials) D4543.
[30] ASTM Standard 2009 Standard Test Method for Pulse Velocity Through Concrete (Philadelphia, PA: American Society for Testing and Materials) C597
[31] ISRM 1981 Rock Characterization Testing and Monitoring International Society of Rock Mechanics Suggested Methods.
[32] ISRM 2007 The Complete ISRM Suggested Methods for Rock Characterization Testing and Monitoring:1974–2006 ed R Ulusay and J A Hudson.
[33] Garia, S., Pal, A.K., Ravi, K. et al. A comprehensive analysis on the relationships between elastic wave velocities and petrophysical properties of sedimentary rocks based on laboratory measurements. J Petrol Explor Prod Technol 9, 2019. p.1869–1881
[34] Soroush H, Qutob H, Oil W, Me T. Evaluation of rock properties using ultrasonic pulse technique and correlating static to dynamic elastic constants. In: 2nd south Asian geoscience conference and exhibition, GEOIndia 2011, Greater Noida, New Delhi, India.
[35] Kahraman, S., Yeken, T. Determination of physical properties of carbonate rocks from P-wave velocity. Bull Eng Geol Environ 67, 2008. p. 277–281
[36] Liu, Jing Sen, Hai Bo Li, Bo Liu, Guo Kai Zhang, and Wei Zhou. “Relation between Uniaxial Compressive Strength and Physical Parameters of Rock in a Nuclear Power Plant.” Applied Mechanics and Materials 865 ,2017. p.373–82.
[37] Arthur Menier, Régis Roy Grant Harrison, Ryan W. Zerff, and Dwayne Kinar, Relationship between rock physical properties and spectral mineralogy applied to exploration for an unconformity-related uranium deposit (Saskatchewan, Canada), Canadian Journal of Earth Sciences. 2020.
[38] Kumar S., Mishra A.K., Choudhary B.S. P and S wave velocity of rocks in Jharia coalfield region for assessment of its geotechnical properties in dry, semi-saturated and saturated conditions, Annales de Chimie - Science des Matériaux, Vol. 41, No. 3-4,2017. p. 209-223.
[39] Parkhomenko, E. I. Electrical properties of rocks, New York, Plenum Press,1967. p.314.
[40] M. HemmatiNourani, M.Taheri Moghadder, M.Safari. Classification and assessment of rock mass parameters in Choghart iron mine using P-wave velocity, Journal of Rock Mechanics and Geotechnical Engineering, Volume 9, 2017. p.318-32.
[41] Rajabzadeh, M.A., Moosavinasab, Z. & Rakhshandehroo, G. Effects of Rock Classes and Porosity on the Relation between Uniaxial Compressive Strength and Some Rock Properties for Carbonate Rocks. Rock Mech Rock Eng 45, 2012. p. 113–122.
[42] Archie, G. E. The Electrical Resistivity Log as an Aid in Determining Some Reservoir. Characteristics. Society of Petroleum Engineers, 1942
[43] Malehmir, A., G Bellefleur. Reflection seismic imaging and physical properties of base-metal and associated iron deposits in the Bathurst Mining Camp, New Brunswick, Canada. Ore Geology Reviews, No. 38 (4), 2010. p.319-333.
[44] Salisbury, M.H., Milkereit, B., Ascough, G.L., Adair, R., Schmitt,D., and Matthews, L. Physical properties and seismic ima-ging of massive sulphides. In Proceedings of exploration 97, 4thdecennial international conference on mineral exploration, Tor-onto, Ont. Edited by A.G. Gubins. Prospectors and Developers Assocication of Canada, 1997. p. 383–390.
[45] André Revil, Florsch, Nicolas & Mao, Deqiang. Induced polarization response of porous media with metallic particles — Part 1: A theory for disseminated semiconductors. GEOPHYSICS. 80, 2015.
[46] A. Ghorbani, A. Revil, A. Coperey, A. Soueid Ahmed, S. Roque, M.J. Heap, H. Grandis, F. Viveiros,Complex conductivity of volcanic rocks and the geophysical mapping of alteration in volcanoes,Journal of Volcanology and Geothermal Research,Volume 357,2018.
[47] Schetselaar E, Bellefleur G, Hunt P. Elucidating the Effects of Hydrothermal Alteration on Seismic Reflectivity in the Footwall of the Lalor Volcanogenic Massive Sulfide Deposit, Snow Lake, Manitoba, Canada. Minerals. 9(6), 2019. p. 384.
|
|
آمار
تعداد مشاهده مقاله: 826
تعداد دریافت فایل اصل مقاله: 517