Simulation of the Effect of Cable Indent Shape on the Shear Behavior of Concrete-Cable Interaction Surface using PFC2D | ||
| روش های تحلیلی و عددی در مهندسی معدن | ||
| مقاله 6، دوره 10، شماره 25، دی 1399، صفحه 61-75 اصل مقاله (2.71 M) | ||
| نوع مقاله: مقاله پژوهشی | ||
| شناسه دیجیتال (DOI): 10.29252/anm.2021.14455.1452 | ||
| نویسنده | ||
| وهاب سرفرازی* | ||
| دانشکده مهندسی معدن، دانشگاه صنعتی همدان | ||
| چکیده | ||
| In this paper, the effect of cable indent shape on the shear behavior of concrete-cable attachment surface has been investigated using PFC2D. Firstly, calibration of PFC was performed using the Brazilian experimental test and uniaxial compression test to reproduce the concrete sample. After calibration of PFC2D, punch shear tests were simulated by creating a rectangular concrete model in PFC2D. Numerical models with a dimension of 100mm *100 mm were prepared. cable with different indent shape was inserted within the model. The punch shear test condition was added to the model. The normal load was fixed at 3.7 MPa (σc/10) and shear load was applied to the model till failure occurred. The results show that tensile cracks are the dominant mode of failure that occurs in the attachment surface. Also, the shape of the attachment surface has an important effect on the failure mechanism of concrete. The shear strength increased by increasing both of the bolt indent width and length. | ||
| کلیدواژه‌ها | ||
| Shear Strength؛ Indent Shape؛ Concrete Bolt؛ PFC2D | ||
| عنوان مقاله [English] | ||
| Simulation of the Effect of Cable Indent Shape on the Shear Behavior of Concrete-Cable Interaction Surface using PFC2D | ||
| نویسندگان [English] | ||
| Vahhab Sarfarazi | ||
| Dept. of Mining, Hamedan University of Technology, Iran | ||
| چکیده [English] | ||
| In this paper, the effect of cable indent shape on the shear behavior of concrete-cable attachment surface has been investigated using PFC2D. Firstly, calibration of PFC was performed using the Brazilian experimental test and uniaxial compression test to reproduce the concrete sample. After calibration of PFC2D, punch shear tests were simulated by creating a rectangular concrete model in PFC2D. Numerical models with a dimension of 100mm *100 mm were prepared. cable with different indent shape was inserted within the model. The punch shear test condition was added to the model. The normal load was fixed at 3.7 MPa (σc/10) and shear load was applied to the model till failure occurred. The results show that tensile cracks are the dominant mode of failure that occurs in the attachment surface. Also, the shape of the attachment surface has an important effect on the failure mechanism of concrete. The shear strength increased by increasing both of the bolt indent width and length. | ||
| کلیدواژه‌ها [English] | ||
| Shear Strength, Indent Shape, Concrete Bolt, PFC2D | ||
| مراجع | ||
|
[1] Stimpson, B. A simplified rock mass-rock bolt interaction analysis for horizontally layered strata. Geotech. Geol. Eng. 1991, 9, 27–51.
[2] Wang, G.; Han, W.; Jiang, Y.; Luan, H.; Wang, K. Coupling Analysis for Rock Mass Supported with CMC or CFC Rockbolts Based on Viscoelastic Method. Rock Mech. Rock Eng. 2019, 52, 4565–45883.
[3] Bjurström, S. Shear strength of hard rock joint hard rock joints reinforced by grouted untensioned bolts. In Proceedings of the Third Congress of the International Society for Rock Mechanics, Denver, CO, USA, 1–7 September 1974; pp. 1194–1199.
[4] Gerrard, C. Rock Bolting in Theory-A Keynote Lecture. In Proceedings of the International Symposium on Rock Bolting, Abisko, Sweden, 28 August–2 September 1983; A. A. Balkema: Rotterdam, The Netherlands, 1984; pp. 3–32.
[5] Spang, K.; Egger, P. Actionoffully-grouted bolts in jointed rock and factors of influence. Rock Mech. Rock Eng. 1990, 23, 201–229.
[6] Chen, N.; Zhang, X.; Jiang, Q.; Feng, X.; Wei, W.; Yi, B. Shear Behavior of Rough Rock Joints Reinforced by Bolts. Int. J. Geomech. 2018, 18, 04017130.
[7] Zhang, X.; Jiang, Q.; Kulatilake, P.; Xiong, F.; Yao, C. Influence of Asperity Morphology on Failure Characteristics and Shear Strength Properties of Rock Joints under Direct Shear Tests. Int. J. Geomech. 2018, 19, 04018196.
[8] Pellet, F.; Egger, P. Analytical model for the mechanical behaviour of bolted rock joints subjected to shearing. Rock Mech. Rock Eng. 1996, 29, 73–97.
[9] Ferrero, A.M. The shear strength of reinforced rock joints. Int. J.RockMech. Min. Sci. Geomech. Abstr. 1995, 32, 595–605.
[10] Liu, A.Q.; Ju, W.J. Analysis of Shear Resisting Action of Full-length Anchored Bolt with Pre-stress. Coal Min. Technol. 2012, 17, 45–48.
[11] Selvadurai, A.P.S.; Yu, Q. Mechanics of a discontinuity in a geomaterial. Comput. Geotech. 2005, 32, 92–106.
[12] Bahaaddini, M.; Sharrock, G.; Hebblewhite, B.K. Numerical direct shear tests to model the shear behaviour of rock joints. Comput. Geothech. 2013, 51, 101–115.
[13] Zhou, Y.; Misra, A.; Shunchuan, W.U.; Zhang, X. Macro-and meso-analyses of rock joint direct shear test using particle flow thory. Chin. J. Rock Mech. Eng. 2012, 31, 1245–1256.
[14] H.C.Andrade, E.D.Leone, An enriched dual boundary element method formulation for linear elastic crack propagation, Engineering Analysis with Boundary Elements, Volume 121, December 2020, Pages 158-179.
[15] Alexander H.‐D. Cheng Emmanuel Detournay, A direct boundary element method for plane strain poroelasticity, International Journal for Numerical and Analytical Methods in Geomechanics, vol. 12, issue 5, pp. 551-572. 1988.
[16] MF Marji, H Hosseini-Nasab, AH Kohsary, A new cubic element formulation of the displacement discontinuity method using three special crack tip elements for crack analysis, JP J. Solids Struct 1 (1), 61-91, 2007.
[17] M Behnia, K Goshtasbi, MF Marji, A Golshani, Numerical simulation of crack propagation in layered formations, Arabian Journal of Geosciences 7 (7), 2729-2737, 2014. In this paper, the finite difference and discrete element methods are used to simulate the shear behavior of rock-rock bolt interface. [18] Park, J.W.; Song,J.J. Numerical simulation of a direct shear test on a rock joint using abonded-particle model. Int. J. Rock Mech. Min. Sci. 2009, 46, 1315–1328.
[19] Zhao, T.B.; Yin, Y.C.; Tan, Y.L.; Qiu, Y. Mechanical Test of Bolt Interface and Microscopic Simulation of Transfer Law for Shear Stress. J. Min. Saf. Eng. 2011, 28, 220–224.
[20] Dugdale, D.S. Yielding of steel sheets containing slits. J. Mech. Phys. Solids 1960, 8, 100–104.
[21] Barenblatt, G.I. The Mathematical Theory of Equilibrium Cracks in Brittle Fracture. Adv. Appl. Mech. 1962, 7, 55–129.
[22] Qiao, P.; Chen, Y. Cohesive fracture simulation and failure modes of FRP–concrete bonded interfaces. Theor. Appl. Fract. Mech. 2008, 49, 213–225.
[23] Hawileh, R.A.; Naser, M.Z.; Abdalla, J.A. Finite element simulation of reinforced concrete beams externally strengthened with short-length CFRP plates. Compos. Part B Eng. 2013, 45, 1722–1730.
[24] Cameselle-Molares, A.; Vassilopoulos, A.P.; Renart, J.; Turon, A.; Keller, T. Numerical simulation of two-dimensional in-plane crack propagation in FRP laminates. Compos. Struct. 2018, 200, 396–407.
[25] Su,X.T.; Yang,Z.J.; Liu,G.H. Monte Carlo simulation of complex cohesive fracture in random heterogeneous quasi-brittle materials: A 3D study. Int. J. Solids Struct. 2010, 47, 2336–2345.
[26] Bahaaddini, M., Sharrock, G., Hebblewhite, B. K. “Numerical investigation of the effect of joint geometrical parameters on the mechanical properties of a non-persistent jointed rock mass under uniaxial compression.” Computers and Geotechnics. 49, pp. 206−225. 2013.
[27] D. O. Potyondy and P. A. Cundall, “A bonded-particle model for rock,” International Journal of Rock Mechanics and Mining Sciences, vol.41, no.8, pp.1329–1364, 2004.
[28] Ghazvinian, A., Sarfarazi, V., Schubert, W. and Blumel, M. (2012), “A study of the failure mechanism of planar non-persistent open joints using PFC2D”, Rock Mech. Rock Eng., 45(5), 677-693. | ||
|
آمار تعداد مشاهده مقاله: 456 تعداد دریافت فایل اصل مقاله: 515 |
||